The Beginner’s Guide to Linux Disk Utilities

Knowing how to check the condition of your hard disk is useful to determine when to replace your hard disk. In today’s article, we will show you some Linux disk utilities to diagnose the health of your hard disk.

Image by Scoobay

S.M.A.R.T System

Most modern ATA and SCSI hard disks have a Self-Monitoring, Analysis, and Reporting Technology (SMART) system. SMART hard disks internally monitor their own health and performance.

The SMART tool assesses the condition of your hard disk based on: the throughput of the hard disk, the seek errors rate of the magnetic heads, and other attributes that your hard disk manufacturer built into their hard disk.

Most implementations of SMART systems allow users to perform self-tests to monitor the performance and reliability of their hard disks. The simplest way to perform a SMART system test with Ubuntu is using the ‘Disk Utility’ under the ‘System’ > ‘Administration’ menu.



The disk utility lets you see the model, serial number, firmware, and the overall health assessment of the hard disk, as well as whether a SMART system is enabled on the hard disk.

The ‘SMART data’ button lets you see the SMART features of your hard disk.

The ‘Run Self-test’ button lets you initiate a short,extended, or a conveyance self-test on the hard disk.

When you execute these tests, you’ll see a progress meter, letting you see how far through the test is and what the estimated time of completion is.

The ‘Attributed section’ lets you see the errors and self-test information.

File System Check

There some other tools, beside the Disk Utility GUI, that we can use to diagnose the health of our hard disk. The File System Check (FSCK), that only comes as a command line tool, is one of the tools that we often use to check the condition of our hard disk.

You can use the ‘Check Filesystem’ feature of the ‘Disk Utility’ to perform the same check,if you are not a command line geek like us.

Of course, there are some situations where we have to use the command line tool to check our file system. For example when we are using a headless system, when our Linux box fails to boot, or when we simply want to show off our command line Kungfu skills to our friends.

At first, the FSCK command line tool looks like something that only a computer geek can handle; But you will find that FSCK is a very easy tool to use. There is one thing to note before you run FSCK; You need to unmount the file system using the ‘umount’ command. Fixing a mounted file system with FSCK could end up creating more damage than the original problem.

sudo umount /dev/sdb

The FSCK command is pretty straightforward:

sudo fsck -t ext4 /dev/sdb

This command checks an ext4 file system (/dev/sdb) for inconsistencies. You should replace /dev/sdb with your own partition. You can run the ‘fdisk’ command to find out your system partitions:

sudo fdisk -l

Scheduled File System Checks

If you’re using Ubuntu, you will notice that Ubuntu runs an FSCK session when you boot your system from time to time. If you find this scheduled check annoying, you can re-schedule the scan using the ‘tune2fs’ command. Here’s how it typically looks like:

The mount count parameter tells us that Ubuntu scans our hard disk after 33 disk mounts.

We can configure the mount count using the ‘-c’ option:

sudo tune2fs -c 35 /dev/sda1

This command will re-configure Ubuntu to scan our hard disk after 35 hard disk mounts when the system boots.

Note: change ‘/dev/sda1/’ with your own partition

 

Bad Blocks

A bad sector is a sector on a computer’s disk drive that cannot be used due to permanent damage (or an OS inability to successfully access it), such as physical damage to the disk surface.

There are two ways to detect bad sectors in Linux: you can use the Disk Utility GUI, or if you are a command line geek like us, you can use the badblocks command to check your hard disk for bad sectors:

sudo badblocks -v /dev/sdb1

Badblock will give us the number of bad sectors in our hard disk.


zainul@zainul-laptop:~$ sudo badblocks -v /dev/sdb1
Checking blocks 0 to 97683200
Checking for bad blocks (read-only test): 3134528 done, 3:27 elapsed
3134560 done, 8:33 elapsed
3134561 done, 10:15 elapsed
3134562 done, 11:57 elapsed
3134563 done, 13:39 elapsed
done
Pass completed, 5 bad blocks found.

 

You have two options when you see bad blocks. You can either look for a new hard disk, or mark these bad blocks as unusable hard disk sectors. This involves two steps:

First we have to write the location of the bad sectors into a flat file.

sudo badblocks /dev/sdb > /home/zainul/bad-blocks

After that, we need to feed the flat file into the FSCK command to mark these bad sectors as ‘unusable’ sectors.

sudo fsck -l bad-blocks /dev/sdb

 


FSCK, Badblocks, and Disk Utility are some of the disk utilities that we often use to scan our hard disks. Do share with the other fellow readers if you know other Linux disk utilities to scan hard disks.

Zainul spends his time trying to make technology more productive, whether it’s Microsoft Office applications, or learning to use web applications to save time.